Bluetooth: Peripheral GATT Discovery Manager

The Peripheral GATT Discovery Manager sample demonstrates how to use the GATT Discovery Manager.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Board target

nRF54LV10 DK

PCA10188

nrf54lv10dk

nrf54lv10dk/nrf54lv10a/cpuapp/ns nrf54lv10dk/nrf54lv10a/cpuapp

nRF54LM20 DK

PCA10184

nrf54lm20dk

nrf54lm20dk/nrf54lm20b/cpuapp/ns nrf54lm20dk/nrf54lm20b/cpuapp nrf54lm20dk/nrf54lm20a/cpuapp/ns nrf54lm20dk/nrf54lm20a/cpuapp

nRF54LC10 DK

PCA10226

nrf54lc10dk

nrf54lc10dk/nrf54lc10a/cpuapp/ns nrf54lc10dk/nrf54lc10a/cpuapp

nRF54L15 DK

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l15/cpuapp/ns nrf54l15dk/nrf54l15/cpuapp

nRF54L15 DK (emulating nRF54L10)

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l10/cpuapp

nRF54L15 DK (emulating nRF54L05)

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l05/cpuapp

nRF54H20 DK

PCA10175

nrf54h20dk

nrf54h20dk/nrf54h20/cpuapp

nRF5340 DK

PCA10095

nrf5340dk

nrf5340dk/nrf5340/cpuapp/ns nrf5340dk/nrf5340/cpuapp

nRF52 DK

PCA10040

nrf52dk

nrf52dk/nrf52832

nRF52840 DK

PCA10056

nrf52840dk

nrf52840dk/nrf52840

For more security, it is recommended to use the */ns variant of the board target. When built for this variant, the sample is configured to compile and run as a non-secure application using security by separation. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

The sample also requires a device to connect to the peripheral, for example, a phone or a tablet with nRF Connect for Mobile or nRF Toolbox.

Overview

When connected to another device, the sample discovers the services of the connected device and outputs the service information.

Building and running

This sample can be found under samples/bluetooth/peripheral_gatt_dm in the nRF Connect SDK folder structure.

For more security, it is recommended to use the */ns variant of the board target (see the Requirements section above.) When built for this variant, the sample is configured to compile and run as a non-secure application using security by separation. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Testing

After programming the sample to your dongle or development kit, test it by performing the following steps. This testing procedure assumes that you are using nRF Connect for Mobile.

  1. Connect the kit to the computer using a USB cable. The kit is assigned a serial port. Serial ports are referred to as COM ports on Windows, /dev/ttyACM devices on Linux, and /dev/tty devices on macOS. To list Nordic Semiconductor devices connected to your computer together with their serial ports, open a terminal and run the nrfutil device list command. Alternatively, check your operating system’s device manager or its equivalent.

  2. Connect to the kit with a terminal emulator (for example, the Serial Terminal app). See Testing and optimization for the required settings and steps.

  3. Connect to the device from nRF Connect (the device is advertising as “Nordic Discovery Sample”). When connected, the sample starts discovering the services of the connected device.

  4. Observe that the services of the connected device are printed in the terminal emulator.

Dependencies

This sample uses the following nRF Connect SDK libraries:

In addition, it uses the following Zephyr libraries:

  • include/zephyr/types.h

  • lib/libc/minimal/include/errno.h

  • include/sys/printk.h

  • include/sys/byteorder.h

  • API:

    • include/bluetooth/bluetooth.h

    • include/bluetooth/hci.h

    • include/bluetooth/conn.h

    • include/bluetooth/uuid.h

    • include/bluetooth/gatt.h

The sample also uses the following secure firmware component: